CODE: SMH/S/150X225
BPC Timber to Masonry Joist Hanger – 150mm x 225mm
(Each)
Each
£5.90
10+
£5.58
20+
£5.25
CODE: SMH/S/47X225
BPC Timber to Masonry Joist Hanger – 47mm x 225mm
(Each)
The standard Single Piece Masonry Hanger is designed for building into brickwork or blockwork. As standard all hangers are manufactured from 2.0mm thick Galvanised Steel to BS EN 10346 :... Read more
£2.00
(Each)
Free delivery on orders over £60
Trade prices and bulk discounts
The standard Single Piece Masonry Hanger is designed for building into brickwork or blockwork.
As standard all hangers are manufactured from 2.0mm thick Galvanised Steel to BS EN 10346 : 2009, DX51D + G600 compliant with BS6178: Part 1:1990 and to the requirements of BS5268.
Wide top flange design offers increased loading capacity on masonry with a minimum crushing strength of 2.8N/mm2 and above. Hangers 150mm deep and over are manufactured 10mm less to allow for notching and regularisation of timber joists.
All hangers feature 75mm bearing surface and pre-punched side gussets to allow nail fixing into timber joists with 30 x 3.75mm sherardized square twist nails.
Installation Details
- The back plate of the joist hanger must be flush against the supporting masonry.
- A minimum of 675mm of cured masonry must be in position above the joist hanger flanges before any load is applied.
- Timber joists should be cut square and butt up to the back face of the hanger with a maximum allowed gap of 6mm.
- Nail to the timber joist through all pre-punched holes in each side gusset with 30×3.75mm sherardized square twist nails.
- It is recommended that ceiling joists are notched at the hanger base to achieve a level surface when using plasterboards.
| Product Type | Timber to Masonry |
| Height | 225mm |
| Width | 47mm |
| Depth | 60mm |
| Material | Galvanised Steel |
The standard Single Piece Masonry Hanger is designed for building into brickwork or blockwork.
As standard all hangers are manufactured from 2.0mm thick Galvanised Steel to BS EN 10346 : 2009, DX51D + G600 compliant with BS6178: Part 1:1990 and to the requirements of BS5268.
Wide top flange design offers increased loading capacity on masonry with a minimum crushing strength of 2.8N/mm2 and above. Hangers 150mm deep and over are manufactured 10mm less to allow for notching and regularisation of timber joists.
All hangers feature 75mm bearing surface and pre-punched side gussets to allow nail fixing into timber joists with 30 x 3.75mm sherardized square twist nails.
Installation Details
- The back plate of the joist hanger must be flush against the supporting masonry.
- A minimum of 675mm of cured masonry must be in position above the joist hanger flanges before any load is applied.
- Timber joists should be cut square and butt up to the back face of the hanger with a maximum allowed gap of 6mm.
- Nail to the timber joist through all pre-punched holes in each side gusset with 30×3.75mm sherardized square twist nails.
- It is recommended that ceiling joists are notched at the hanger base to achieve a level surface when using plasterboards.
| Product Type | Timber to Masonry |
| Height | 225mm |
| Width | 47mm |
| Depth | 60mm |
| Material | Galvanised Steel |
Customers also bought
CODE: JHM100225
Simpson Strong-Tie Joist Hangers Masonry – 100 x 225mm
(Each)
Each
£4.02
10+
£3.96
50+
£3.91
CODE: B460/100
BPC Timber to Timber Joist Hanger – 100 x 460mm
(Each)
Each
£2.35
10+
£2.25
20+
£2.12
CODE: CBK60120ZY
Multi Purpose Chipboard Screws – Pozi – 6.0 x 120mm
(Qty: 100)
Each
£6.17
5+
£6.06
10+
£5.84
CODE: CBK50080ZY
Multi Purpose Chipboard Screws – Pozi – 5.0 x 80mm
(Qty: 100)
Each
£2.75
5+
£2.64
10+
£2.53
CODE: CBK50050ZY
Multi Purpose Chipboard Screws – Pozi – 5.0 x 50mm
(Qty: 200)
Each
£3.32
5+
£3.21
10+
£2.99
CODE: 45030CLAF
Classic Multi-Purpose Screws Countersunk – Pozi – 4.5 x 30mm
(Qty: 200)
Each
£3.00
5+
£2.85
10+
£2.70